标准新生牦牛血清（无菌过滤）100ML标准新生牦牛血清（无菌过滤）是一种常用于细胞培养等生物实验和研究的生物制品，以下是关于它的详细介绍：制备过程采血：从出生后未超过 20 天的健康新生牦牛体内采集血液，一般在符合卫生标准和动物福利的条件下，由专业人员操作，采用无菌采血技术，确保血液不受污染。分离血清：采集后的血液在无菌环境下自然凝固或经过离心等方式使血清与血细胞分离，得到粗制的新生牦牛血清。过滤除菌：将粗制血清通过一系列不同孔径的无菌滤膜进行过滤，通常会使用 0.2 微米孔径的滤膜，以去除细菌、真菌、支原体等微生物，获得无菌过滤的标准新生牦牛血清。作用与用途细胞培养：为细胞提供生长所需的营养物质，如氨基酸、维生素、矿物质、脂类、激素等，促进细胞的生长、增殖和贴壁，维持细胞的正常生理功能3。生物制药：在生物制药过程中，用于培养生产药物的细胞株，有助于提高药物产量和质量，也可作为生物制剂的添加成分，增强制剂的稳定性和活性。科研实验：在细胞生物学、分子生物学、免疫学等科研领域的实验中广泛应用，如用于细胞系的建立、细胞信号转导研究、抗体生产等实验项目。质量控制微生物检测：严格检测血清中是否含有细菌、真菌、支原体、病毒等微生物，确保无菌过滤的效果，防止微生物污染对细胞培养和实验结果产生影响。内毒素检测：内毒素含量是衡量血清质量的重要指标之一，内毒素过多会对细胞产生毒性作用，影响细胞的生长和功能，一般要求标准新生牦牛血清的内毒素含量控制在较低水平。蛋白含量及成分分析：检测血清中各种蛋白质的含量和成分，包括白蛋白、球蛋白、生长因子等，保证血清中营养成分的比例和含量符合细胞培养的要求，并且批次间的蛋白含量和成分稳定。储存与使用储存条件：一般需要在 - 20℃或更低的温度下冷冻保存，以保持血清的活性和稳定性，避免反复冻融，否则会导致血清中的蛋白变性和活性成分丧失。使用方法：在使用前，需要将冷冻的血清在 2-8℃的冰箱中缓慢解冻，解冻后的血清应尽快使用，避免长时间放置在室温下，防止微生物污染和活性成分降解，使用时根据实验要求，将血清添加到细胞培养液中，通常添加比例在 5%-20% 不等。
人（Human）免疫球蛋白G1（IgG1）ELISA检测试剂盒本试剂盒只能用于科学研究，不得用于医学诊断检测原理试剂盒采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被免疫球蛋白G1（IgG1）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的免疫球蛋白G1（IgG1）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。试剂盒组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、1、2、4、8、16 g/L试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。试剂盒性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于0.1 g/L。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Human Immunoglobulin G1 (IgG1) ELISA Kit instruction Intended useThis IgG1 ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of IgG1 in the sample, this IgG1 ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus IgG1 concentration. The concentration of IgG1 in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by: 0,1,2,4,8,16 g/LReagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 0.1 g/L6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
产品名称：优级新生牛血清（无菌过滤）500ml产品规格：100ml/200ml/500ml保 存：-20℃，三年。优级新生牛血清（无菌过滤） 使用时常见问题及解决方法：一、保存血清的方法?血清应保存在-5℃至-2O℃若存放于4℃时，请勿超过一个月。若您一次无法用完一瓶，建议将无菌分装血清至恰当的灭菌容器内，再放回冷冻。二、如何解冻血清才不会使产品质量受损?将血清从冷冻箱取出后，先置于2-8℃冰箱使之溶解，然后在室温下使之全溶。但必须注意的是，溶解过程中必须规则地摇晃均匀。三、如何避免沉淀物的产生?1.解冻血清时，请按照所建议的逐步解冻法(-2O℃至4℃至室温)，若血清解冻时改变的温度太大(如-20℃至37℃)，实验显示非常容易产生沉淀物。2.解冻血清时，请随时将之摇晃均匀，使温度及成分均一，减少沉淀的发生3.请勿将血清置于37℃太久。若在37℃放置太久，血清会变得混浊，同时血清中许多较不稳定的成分也会因此受到损害，而影响血清的质量。4.血清的热灭活非常容易造成沉淀物的增多，若非必要，可以无须做此步骤。5.若必须做血清的热灭活，请遵守56℃，30分钟的原则，并且随时摇晃均匀。温度过高，时间过久或摇晃不均匀，都会造成沉淀物的增多。四、血清解冻后发现有絮状沉淀物出现，该如何处理? 欲去除这些絮状沉淀物，可以将血清分装至无菌离心管内，以400g稍微离心，上清液即可接着加入培养基内一起过滤。但不建议以过滤的方法去除这些絮状沉淀物，因为它可能会阻塞过滤膜。血清使用注意事项：防止发病免疫血清多用马、牛血液制备，马、牛血清对其它动物来说，也具有抗原性，有引起血清病的可能，因此，使用免疫血清要注意防止引起血清病，预防的主要措施是使用提纯的制品，不用不合格的产品；另外，不要有急功近利的想法，要按照要求剂量使用，一次用量不可过大。Tips：1. 血清的保存：在-15℃以下血清的有效期为5年，4℃可保存数周，不宜室温保存，不宜反复冻融。配制成完全培养基后应在四周内用完，一瓶血清如无法一次用完应无菌分装成恰当数量并冷冻保存。2、血清中的絮状沉淀物：血清是多种蛋白质的混合物，在冻融过程中会出现絮状沉淀物，主要原因是由于血清中脂蛋白和纤维蛋白变性所造成。但并不影响血清本身的质量和使用。如需去除可先400g离心取上清液配制成完全培养基再过滤即可使用。3、血清的解冻：合理的解冻方式可以更好的保护血清质量并可以在＊大程度上减少絮状沉淀物的产生。血清从低温冰箱中取出后，经4℃冰箱、室温、37℃水浴逐步规则摇晃均匀融解，直至完全融解后再使用。4、血清的热灭活：将血清严格56℃水浴均匀加温30分钟可以灭活血清中的补体系统。是不是所有用途的血清都需要热灭活呢？对大多数细胞来说是不需要的。激活的补体能参与溶解细胞，刺激光滑肌收缩，细胞和血小板释放组胺，激活淋巴细胞和巨噬细胞。因此在免疫学研究，培养ES细胞，昆虫细胞和平滑肌肉细胞时，建议使用热灭活血清，在正常情况下加热处理对血清的促细胞生长效应无明显促进作用，甚至会因为加热处理影响血清的质量。5、血清中的“小黑点”现象：血清在经过一段时间的低温冻存再融解后，在正常情况下会出现絮状蛋白沉淀。但往往有用户反应血清中有“小黑点”现象，认为是微生物污染。实验发现血清在37℃环境放置时间过长或经过加热灭活处理，血清中的沉淀物往往会呈增多趋势，这些沉淀物在倒置显微镜下观察，像是“小黑点”，让使用者误以为是血清遭受微生物污染并在分裂增殖。因此如无必要，完全可以不进行热灭活处理并保证血清的低温保存。实验证明使用血清时注意以下几点事项不但可以保证血清质量并能给使用者带来方便：◎血清可在-15℃以下低温保存。◎血清一瓶血清一次无法用完的应分装冻存，分次用完。◎血清按-15℃以下至4℃至室温至37℃逐步均匀解冻使用。◎若非必要，无须进行热灭活。若必须做血清热灭活的，须严格控制在56℃水浴30分钟均匀加热灭活。 主要成分： 血清是由血浆去除纤维蛋白原而形成的一种很复杂的混合物，其组成成份虽大部分已知，但还有一部分尚不清楚，且血清组成及含量常随供血动物的性别、年龄、生li条件和营养条件不同而异。血清是血浆中不含纤维蛋白原的胶状液体，具有维持血液的正常粘度、酸碱度、渗透压等作用。它主要由水和各种化学成分组成，这些化学成分包括白蛋白、α1、α2、β、γ-球蛋白，甘油三酯，总胆固醇，谷丙转氨酶等。血清中含有各种血浆蛋白、多肽、脂肪、碳水化合物、生长因子、激素、无机物等，这些物质对促进细胞生长或抑制生长活性是达到生li平衡的。
产品名称：优级新生牛血清（无菌过滤）200ml产品规格：100ml/200ml/500ml保 存：-20℃，三年。优级新生牛血清（无菌过滤） 使用时常见问题及解决方法：一、保存血清的方法?血清应保存在-5℃至-2O℃若存放于4℃时，请勿超过一个月。若您一次无法用完一瓶，建议将无菌分装血清至恰当的灭菌容器内，再放回冷冻。二、如何解冻血清才不会使产品质量受损?将血清从冷冻箱取出后，先置于2-8℃冰箱使之溶解，然后在室温下使之全溶。但必须注意的是，溶解过程中必须规则地摇晃均匀。三、如何避免沉淀物的产生?1.解冻血清时，请按照所建议的逐步解冻法(-2O℃至4℃至室温)，若血清解冻时改变的温度太大(如-20℃至37℃)，实验显示非常容易产生沉淀物。2.解冻血清时，请随时将之摇晃均匀，使温度及成分均一，减少沉淀的发生3.请勿将血清置于37℃太久。若在37℃放置太久，血清会变得混浊，同时血清中许多较不稳定的成分也会因此受到损害，而影响血清的质量。4.血清的热灭活非常容易造成沉淀物的增多，若非必要，可以无须做此步骤。5.若必须做血清的热灭活，请遵守56℃，30分钟的原则，并且随时摇晃均匀。温度过高，时间过久或摇晃不均匀，都会造成沉淀物的增多。四、血清解冻后发现有絮状沉淀物出现，该如何处理? 欲去除这些絮状沉淀物，可以将血清分装至无菌离心管内，以400g稍微离心，上清液即可接着加入培养基内一起过滤。但不建议以过滤的方法去除这些絮状沉淀物，因为它可能会阻塞过滤膜。血清使用注意事项：防止发病免疫血清多用马、牛血液制备，马、牛血清对其它动物来说，也具有抗原性，有引起血清病的可能，因此，使用免疫血清要注意防止引起血清病，预防的主要措施是使用提纯的制品，不用不合格的产品；另外，不要有急功近利的想法，要按照要求剂量使用，一次用量不可过大。Tips：1. 血清的保存：在-15℃以下血清的有效期为5年，4℃可保存数周，不宜室温保存，不宜反复冻融。配制成完全培养基后应在四周内用完，一瓶血清如无法一次用完应无菌分装成恰当数量并冷冻保存。2、血清中的絮状沉淀物：血清是多种蛋白质的混合物，在冻融过程中会出现絮状沉淀物，主要原因是由于血清中脂蛋白和纤维蛋白变性所造成。但并不影响血清本身的质量和使用。如需去除可先400g离心取上清液配制成完全培养基再过滤即可使用。3、血清的解冻：合理的解冻方式可以更好的保护血清质量并可以在＊大程度上减少絮状沉淀物的产生。血清从低温冰箱中取出后，经4℃冰箱、室温、37℃水浴逐步规则摇晃均匀融解，直至完全融解后再使用。4、血清的热灭活：将血清严格56℃水浴均匀加温30分钟可以灭活血清中的补体系统。是不是所有用途的血清都需要热灭活呢？对大多数细胞来说是不需要的。激活的补体能参与溶解细胞，刺激光滑肌收缩，细胞和血小板释放组胺，激活淋巴细胞和巨噬细胞。因此在免疫学研究，培养ES细胞，昆虫细胞和平滑肌肉细胞时，建议使用热灭活血清，在正常情况下加热处理对血清的促细胞生长效应无明显促进作用，甚至会因为加热处理影响血清的质量。5、血清中的“小黑点”现象：血清在经过一段时间的低温冻存再融解后，在正常情况下会出现絮状蛋白沉淀。但往往有用户反应血清中有“小黑点”现象，认为是微生物污染。实验发现血清在37℃环境放置时间过长或经过加热灭活处理，血清中的沉淀物往往会呈增多趋势，这些沉淀物在倒置显微镜下观察，像是“小黑点”，让使用者误以为是血清遭受微生物污染并在分裂增殖。因此如无必要，完全可以不进行热灭活处理并保证血清的低温保存。实验证明使用血清时注意以下几点事项不但可以保证血清质量并能给使用者带来方便：◎血清可在-15℃以下低温保存。◎血清一瓶血清一次无法用完的应分装冻存，分次用完。◎血清按-15℃以下至4℃至室温至37℃逐步均匀解冻使用。◎若非必要，无须进行热灭活。若必须做血清热灭活的，须严格控制在56℃水浴30分钟均匀加热灭活。 主要成分： 血清是由血浆去除纤维蛋白原而形成的一种很复杂的混合物，其组成成份虽大部分已知，但还有一部分尚不清楚，且血清组成及含量常随供血动物的性别、年龄、生li条件和营养条件不同而异。血清是血浆中不含纤维蛋白原的胶状液体，具有维持血液的正常粘度、酸碱度、渗透压等作用。它主要由水和各种化学成分组成，这些化学成分包括白蛋白、α1、α2、β、γ-球蛋白，甘油三酯，总胆固醇，谷丙转氨酶等。血清中含有各种血浆蛋白、多肽、脂肪、碳水化合物、生长因子、激素、无机物等，这些物质对促进细胞生长或抑制生长活性是达到生li平衡的。
小鼠（Mouse）微小病毒 IgG 抗体 （MVM -IgG ）ELISA检测试剂盒本试剂盒只能用于科学研究，不得用于医学诊断检测原理试剂盒采用间接法酶联免疫吸附试验（ELISA）。往预先包被微小病毒 IgG抗原的包被微孔中，依次加入标本、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。用酶标仪在450nm波长下测定吸光度（OD 值），与CUTOFF值相比较，从而判定标本中微小病毒 IgG 抗体 （MVM -IgG ）的存在与否。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 预处理后的样本无需稀释，直接取50μL加样即可。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。试剂盒组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无阴性对照0.5mL 0.5mL 无阳性对照0.5mL 0.5mL 无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释样本稀释液6mL3mL无底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无 试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置阴、阳性对照孔和样本孔，阴、阳性对照孔中加入阴性对照、阳性对照各50μL；3. 待测样本孔加待测样本50μL；4. 随后阴、阳性对照孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 1. 试验有效性：阳性对照孔OD值平均值≥1.00； 阴性对照孔OD值平均值≤0.15。2. 临界值（Cut off）计算：临界值=阴性对照孔平均值+0.153. 阴性判断：样品OD值＜临界值（Cut off），样品为阴性4. 阳性判断：样品OD值＞临界值（Cut off），样品为阳性试剂盒性能1. 准确性：阳性对照孔OD值平均值≥1.00；阴性对照孔OD值平均值≤0.15，说明试验结果有效。2. 特异性：不与其它可溶性结构类似物交叉反应。3. 重复性：板内、板间变异系数均小于15%。4. 贮藏：2-8℃，避光防潮保存。5. 有效期：6个月免责声明1. 试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。
细菌(Bacteria）ATP酶（ATPase）ELISA检测试剂盒本试剂盒只能用于科学研究，不得用于医学诊断检测原理试剂盒采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被ATP酶（ATPase）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的ATP酶（ATPase）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品活性。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。试剂盒组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、12.5、25、50、100、200 U/L试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 试剂盒性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于1.0 U/L。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Bacteria ATPase ELISA Kit instruction Intended useThis ATPase ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures. The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of ATPase in the sample, this ATPase ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus ATPase concentration. The concentration of ATPase in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by:0,12.5,25,50,100,200 U/LReagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 1.0 U/L6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
细菌（Bacteria）GTP酶（GTPase）ELISA检测试剂盒本试剂盒只能用于科学研究，不得用于医学诊断检测原理试剂盒采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被GTP酶（GTPase）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的GTP酶（GTPase）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品活性。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。试剂盒组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、5、10、20、40、80 U/L试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。 4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 试剂盒性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于1.0 U/L。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Bacteria GTPase ELISA Kit instruction Intended useThis GTPase ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of GTPase in the sample, this GTPase ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus GTPase concentration. The concentration of GTPase in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by:0,5,10,20,40,80 U/LReagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 1.0 U/L6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
鸡（Chicken）总三碘甲状腺原氨酸（TT3）ELISA检测试剂盒本试剂盒只能用于科学研究，不得用于医学诊断检测原理试剂盒采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被总三碘甲状腺原氨酸（TT3）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的总三碘甲状腺原氨酸（TT3）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。试剂盒组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、0.5、1、2、4、8 ng/mL试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 试剂盒性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于0.1 ng/mL。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。
人（Human）多巴胺（DA）ELISA检测试剂盒本试剂盒只能用于科学研究，不得用于医学诊断检测原理试剂盒采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被多巴胺（DA）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的多巴胺（DA）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。试剂盒组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、7.5、15、30、60、120 nmol/L试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。 4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 试剂盒性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于1.0 nmol/L。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Human dopamine (DA) ELISA Kit instruction Intended useThis DA ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of DA in the sample, this DA ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus DA concentration. The concentration of DA in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by:0,7.5,15,30,60,120 nmol/LReagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 1.0 nmol/L6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
人（Human）β-内啡肽（β-EP）ELISA检测试剂盒本试剂盒只能用于科学研究，不得用于医学诊断检测原理试剂盒采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被β-内啡肽（β-EP）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的β-内啡肽（β-EP）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。试剂盒组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、2.5、5、10、20、40 pg/mL试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。 4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 试剂盒性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于1.0 pg/mL。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Human Beta-Endorphin (β-EP) ELISA Kit instruction Intended useThis β-EP ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of β-EP in the sample, this β-EP ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus β-EP concentration. The concentration of β-EP in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by:0,2.5,5,10,20,40 pg/mlReagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 1.0 pg/ml6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
31011502012822