大鼠（Rat）乳酸脱氢酶（LDH）ELISA检测试剂盒本试剂盒只能用于科学研究，不得用于医学诊断检测原理试剂盒采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被乳酸脱氢酶（LDH）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的乳酸脱氢酶（LDH）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。试剂盒组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、1.25、2.5、5、10、20 pg/mL试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。 4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 试剂盒性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于0.1 pg/mL。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Rat Lactate Dehydrogenase (LDH) ELISA Kit instruction Intended useThis LDH ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of LDH in the sample, this LDH ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus LDH concentration. The concentration of LDH in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by:0,1.25,2.5,5,10,20 pg/mLReagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 0.1 pg/mL6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
大鼠（Rat）乙酰胆碱（ACH）ELISA检测试剂盒本试剂盒只能用于科学研究，不得用于医学诊断检测原理试剂盒采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被乙酰胆碱（ACH）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的乙酰胆碱（ACH）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。试剂盒组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、2.5、5、10、20、40 ng/ml试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 试剂盒性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于1.0ng/ml。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Rat acetylcholine (ACH) ELISA Kit instruction Intended useThis ACH ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of ACH in the sample, this ACH ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus ACH concentration. The concentration of ACH in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by:0,2.5,5,10,20,40 ng/ml.Reagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 4. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.5. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.6. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.7. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 1.0 ng/ml6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
大鼠（Rat）一氧化氮（NO）ELISA检测试剂盒本试剂盒只能用于科学研究，不得用于医学诊断检测原理试剂盒采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被一氧化氮（NO）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的一氧化氮（NO）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。试剂盒组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、2.5、5、10、20、40μmol/ L试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 试剂盒性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于0.1μmol/L。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Rat nitric oxide (NO) ELISA Kit instruction Intended useThis NO ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of NO in the sample, this NO ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus NO concentration. The concentration of NO in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubes Sample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by:0,2.5,5,10,20,40 μmol/LReagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add Sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 0.1μmol/L6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
大鼠（Rat）三磷酸腺苷（ATP）ELISA检测试剂盒本试剂盒只能用于科学研究，不得用于医学诊断检测原理试剂盒采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被三磷酸腺苷（ATP）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的三磷酸腺苷（ATP）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。试剂盒组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、400、800、1600、3200、6400 nmol/L试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 试剂盒性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于10 nmol/L。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Rat ATP ELISA Kit instruction Intended useThis ATP ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of ATP in the sample, this ATP ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus ATP concentration. The concentration of ATP in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by:0,400,800,1600,3200,6400 nmol/LReagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add esting sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 10 nmol/L6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
大鼠（Rat）转化生长因子β（TGF-β）ELISA检测试剂盒本试剂盒只能用于科学研究，不得用于医学诊断检测原理试剂盒采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被转化生长因子β（TGF-β）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的转化生长因子β（TGF-β）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。试剂盒组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、15、30、60、120、240 pg/mL试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 试剂盒性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于1.0 pg/mL。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Rat Transforming Growth factor β (TGF-β) ELISA Kit instruction Intended useThis TGF-β ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of TGF-β in the sample, this TGF-β ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus TGF-β concentration. The concentration of TGF-β in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by:0,15,30,60,120,240 pg/mlReagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 1.0 pg/ml6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
小鼠（Mouse）喹啉酸（QUIN）ELISA检测试剂盒本试剂盒只能用于科学研究，不得用于医学诊断检测原理试剂盒采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被喹啉酸（QUIN）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的喹啉酸（QUIN）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。试剂盒组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、50、100、200、400、800 nmol/L试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 试剂盒性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于10 nmol/L。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Mouse Quinolinic acid (QUIN) ELISA Kit instruction Intended useThis QUIN ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of QUIN in the sample, this QUIN ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus QUIN concentration. The concentration of QUIN in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by:0,50,100,200,400,800 nmol/LReagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 10 nmol/L6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
斑马鱼（Zebrafish）白细胞介素6（IL-6）ELISA检测试剂盒本试剂盒只能用于科学研究，不得用于医学诊断检测原理试剂盒采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被白细胞介素6（IL-6）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的白细胞介素6（IL-6）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。试剂盒组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、7.5、15、30、60、120 pg/mL试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 试剂盒性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于1.0 pg/mL。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Zebrafish Interleukin 6 (IL-6) ELISA Kit instruction Intended useThis IL-6 ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of IL-6 in the sample, this IL-6 ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus IL-6 concentration. The concentration of IL-6 in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by:0,7.5,15,30,60,120 pg/ml.Reagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 1.0 pg/ml6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
斑马鱼（Zebrafish）肿瘤坏死因子α（TNF-α）ELISA检测试剂盒本试剂盒只能用于科学研究，不得用于医学诊断检测原理试剂盒采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被肿瘤坏死因子α（TNF-α）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的肿瘤坏死因子α（TNF-α）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。试剂盒组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、40、80、160、320、640 pg/mL试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL(即样本稀释5倍)；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 试剂盒性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于1.0 pg/mL。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Zebrafish Tumor necrosis factor α (TNF-α) ELISA Kit instruction Intended useThis TNF-α ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of TNF-α in the sample, this TNF-α ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus TNF-α concentration. The concentration of TNF-α in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by:0,40,80,160,320,640 pg/ml.Reagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add 40μl of Sample Diluent to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 1.0 pg/ml6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
猪血清（无菌过滤）100ml以下是关于猪血清（无菌过滤）的相关介绍：基本信息定义：猪血清是猪血在凝固后，经离心或自然沉淀，去除上层血浆和下层血细胞等成分，得到的淡黄色透明液体。无菌过滤则是通过特定的过滤技术和设备，去除猪血清中的细菌、真菌、支原体等微生物，使其达到无菌状态，可用于细胞培养、生物制药等对无菌条件要求较高的领域。外观：正常情况下为淡黄色透明液体，颜色可能因猪的品种、饮食、采血时间等因素而略有差异。制备过程采血：使用无菌干燥玻璃容器从屠宰场采集猪血，盛取猪血前玻璃容器中可加入无菌生理盐水和适量抗生素，如庆大霉素，以防止细菌污染。静置与离心：将采集的猪血在 4℃冰箱静置数小时，待血清自然析出，然后进行离心，通常以 4000rpm 离心 15 分钟左右，进一步分离血清和血细胞等杂质，回收上清液，即得到初步的猪血清。无菌过滤：将初步得到的猪血清通过正压过滤器，使用 0.22μm 或 0.1μm 的滤膜进行过滤除菌，以去除血清中的细菌、真菌和支原体等微生物，得到无菌过滤的猪血清。分装与保存：将无菌过滤后的猪血清进行分装，一般以 100ml / 瓶等规格分装，然后置于 - 20℃冰箱保存备用。作用与用途细胞培养：为细胞提供基本营养物质，如氨基酸、维生素、无机物、脂类物质、核酸衍生物等，是细胞生长必需的物质；还能提供激素和各种生长因子，如胰岛素、肾上腺皮质激素、成纤维细胞生长因子等，促进细胞的生长、增殖和分化。生物制药：在疫苗生产中，如猪肺炎支原体疫苗的生产，猪血清是重要的原材料之一；用于配置各种生物制药所需的培养基和缓冲液等，保证药物生产过程中细胞或微生物的生长和代谢需求。科研实验：在免疫学研究、细胞生物学研究、分子生物学研究等领域广泛应用，可用于研究细胞的生理功能、代谢途径、信号传导等，以及作为免疫检测的试剂或样本，用于检测抗体、抗原等。保存方法低温保存：长期保存的猪血清必须储存于 - 20℃至 - 70℃低温冰箱中，4℃冰箱中保存时间切勿超过 1 个月。预留空间：由于血清结冰时体积会增加约 10%，因此在冻入低温冰箱前，必须预留一定体积空间，否则易发生污染或玻璃瓶冻裂。解冻方法：瓶装血清解冻需采用逐步解冻法，即先将 - 20℃至 - 70℃低温冰箱中的血清放入 4℃冰箱中溶解 1 天，然后移入室温，待全部溶解后再分装，在溶解过程中需不断轻轻摇晃均匀，使温度与成分均一，减少沉淀的发生。
鸡血清（无菌过滤）500ml鸡血清（无菌过滤）是一种在科研和生物医学领域有着广泛应用的产品，以下是其详细介绍：制备：通常采用健康鸡血液为原料，经无菌采集、分离后，再通过微孔过滤分装而成。例如，先将鸡血用离心机离心，收集滤过液并冻存，数天后取出化冻，经粗滤澄清，＊后用灭菌的滤板进行过滤除菌，从而得到无细菌、真菌、支原体等的无菌鸡血清。成分：血清是血浆中不含纤维蛋白原的胶状液体，主要由水和各种化学成分组成，包括白蛋白、α1、α2、β、γ - 球蛋白，甘油三酯，总胆固醇，谷丙转氨酶等。作用：提供基本营养物质：为细胞培养提供氨基酸、维生素、矿物质等多种营养成分，满足细胞生长和代谢的需求。提供激素和生长因子：含有胰岛素、生长激素等激素以及多种生长因子，能够促进细胞的增殖和分化。提供结合蛋白：如转铁蛋白可结合铁离子，为细胞提供铁元素；白蛋白可结合脂肪酸、激素等物质，维持其在培养基中的稳定性和活性。提供促接触和伸展因子：使细胞能够更好地贴壁生长，免受机械损伤，有助于细胞在培养容器表面铺展和生长。对培养中的细胞起到保护作用：可以中和有毒物质，减少细胞氧化应激，降低细胞凋亡的发生率，为细胞提供一个相对稳定和安全的环境。应用：适合于单抗研制、原代和传代细胞培养、规模化培养的疫苗生产、生物医学研究、诊断试剂生产等。例如在制备副鸡嗜血杆菌或禽多杀巴氏杆菌等细菌的培养基时，可作为辅料加入，用于细菌抗原的批量生产，提高细菌培养的含菌量。保存和使用：通常保存在 - 20℃，保质期一般为液体 1 年，冻干粉 3 年。使用时，血清从冰冻区中取出后，应置于 2 - 8℃中使之融化，解冻过程中间歇地轻轻摇晃均匀，待全部溶解后再分装或直接使用。完全融解的血清从 4℃拿出，按要求比例（5% - 20%）加基础培养基配置成全培养基，建议置于 4℃冰箱存放并于 1 - 2 周内用完。在使用鸡血清（无菌过滤）时，有少量蛋白质结块析出通常不影响使用，但未融化或融化未经摇匀的血清禁止直接放入高温水浴内加温，同时应减少血清重复冻融，以避免影响其促细胞生长效果。
31011502012822